Remote SDR V5 -Raspberry 4B or Orange Pi Image Installation
Here is the detailed procedure to install Remote SDR in version 5, on a Raspberry Pi 4B with at least 2 GB of memory or an Orange Pi Zero 2. The latest images written...
Category: Adalm-Pluto
Remote SDR v5 – Manual Installation
GNU RADIO 3.9 – Osmocom – Soapy SDR RTL-SDR – HackRF – Adalm-Pluto – RSP1 – RSP1A – SA818 Below is the detailed procedure for installing Remote SDR in version 5 on a Raspberry...
Remote SDR v5
Web based Transceiver “Remote SDR” is a web application allowing to remotely control an amateur radio transceiver between 1 MHz and 6 GHZ. Its first application was the duplex control of a station allowing...
Troubleshooting
Raspberry / Orange Pi not starting Issue After burning an image to an SD card, the processor does not start. Solution 1 Very often, it is a weak 5v supply that is the source...
SDR Selection
There are many SDRs on the market. In the table below you will find the main characteristics of the compatible “Remote SDR” models. This list will evolve in the future. Nom Band RX TX...
Launch of Remote SDR
In the address bar of Chrome or Edge, enter the IP address of the Orange/Raspberry Pi or one of the 2 Orange Pi if you have a dual configuration. If the system asks you,...
Configurations
COMPACT CONFIGURATION with an ADALM-PLUTO – Rasperry Pi 4 – ETHERNET Avantages Disadvantages – Well-known RPI4 – Wifi or Ethernet– 12 bits of Pluto dynamic – poor stability in frequency of the Adalm-Pluto May...
Characteristics
Characteristics Receiver SDR in reception: RTL-SDR (example: NESDR SMArt from Nooelec) or, HackRF One or, Adalm-Pluto RSP1, RSP1A MSI SDR Frequency: 1 MHz to 6 GHz (depending on the chosen SDR) Spectral band processed:...
Introduction to Remote SDR
Web based Transceiver “Remote SDR” or “SDR Distant” is a web application allowing to remotely control an amateur radio transceiver between 1 MHz and 6 GHZ. Its first application was the duplex control of...
Remote SDR v4
Web based Transceiver “Remote SDR” or “SDR Distant” is a web application allowing to remotely control an amateur radio transceiver between 1 MHz and 6 GHZ. Its first application was the duplex control of...
Remote SDR V4 – Raspberry Pi 4B or Orange Pi Zero 2 image installation
Remote SDR source code and images available on Github Here is the detailed procedure to install Remote SDR version 4 on a Raspberry Pi 4B with at least 2 GB of memory or an...
Remote SDR v4 – Manual Installation
Below is the detailed procedure to install Remote SDR version 4 on a Raspberry Pi 4 B (2GB) or an Orange Pi Zero 2. It is adaptable for other ‘Single Board Computer’ cards if...
Remote SDR v2 – Raspberry 4B image installation
Obsolete. Go here Remote SDR version 2.5 available on Github Here is the detailed procedure to install Remote SDR version 2 on a Raspberry Pi 4B with at least 2 GB of memory. The...
Remote SDR – Examples of realization
Many OM around the world have embarked on the realization of Remote SDR. Below are some examples. Listening EME by BG0DXC / BG0AUB Listening on 23cm. The low bandwidth required to transport signals over...
Remote SDR v2 – Orange Pi One Plus or Orange Pi Zero 2 image installation
Below is the detailed procedure to install Remote SDR in version 2 on an Orange Pi One Plus or an Orange Pi Zero 2. The latest images written on a 32 GB SD card,...
Remote SDR V2 – Manual installation
Below is the detailed procedure to install Remote SDR version 2 on a Raspberry Pi 4 B (2GB), an Orange Pi One Plus or an Orange Pi Zero 2. It is adaptable for other...
Remote SDR V2
Obsolete. Go here now. “Remote SDR” is a web application allowing to remotely control an amateur radio transceiver between 1 MHz and 6 GHZ. Its first application was the duplex control of a station...
SDR Pluto Frequency Update
In this post we will discuss the issue of changing the frequency or gain of the Adalm-Pluto SDR in real time in a GNU Radio application. Indeed, the Pluto is disturbed for a small...
NBFM Transceiver with Pluto SDR and GNU Radio
The first step consists of installing GNU Radio and the interface to Adalm-Pluto or PlutoSDR on an Orange Pi One Plus running under Armbian. Then as an example, we will study the realization of...
Frequency extension of Pluto SDR
The 2021 version of the PlutoSDR uses the AD9363 chip which is limited to a frequency range of 325 to 3800 MHz and a bandwidth of 20 MHz. However, the high-end AD9364 chip which...
SDR Adalm-Pluto setup
In the range of SDRs found on the market, Adalm-Pluto is an interesting solution which is capable of working in Full-Duplex (simultaneous reception and transmission). Please note that the frequency band is between 325...
Recent Comments